What is required:
- main fabric: light linen cut 50 cm;
- fabric finishes: a piece of red linen 30 cm;
- light threads to match the main fabric – 1 PC.;
- red thread in the color of the fabric finish – 1 PC.;
- thick cotton thread for cord – about 5 meters;
- printed picture of deer;
- water-soluble tissue marker;
- scissors;
- sewing machine.
2. The details of the bags
- bag base: two rectangles size 38.0*50.0 cm – 2 details;
- pocket of the main fabric size 15.0*17.0 cm (width – 15);
- bag for storage bags – rectangle 19,0*37,0 cm(with cut oriented vertically);
- red cloth straps 9.0*150.0 cm;
- application "Deer" – a rectangle of red fabric size 13.0*12.0 cm.
3. Collect the bag
Mark and iron
1. On the main parts of the bag on top note 1.0 cm and 2.5 cm from the same edge. It's buckling. Ironed, hiding the edge in the bend.
2. We do the same with the pocket. We iron on the narrower side (15.0 cm), only the bending is done already: 1.0 cm and 2.0 cm.
3. Bend and iron the straps along (lengthwise).
4. Note on the basis of the bags the location of future straps. On each part of the basis of the retreat from the sides of 10 cm and draw vertical lines.
5. We plan the location of the pocket – retreat from the bottom of 13 cm and draw a horizontal line. From the sides retreat 11.5 cm and draw vertical lines up the size of the pocket.
6. Take the ends of the straps (two straps – 4 ends). On the one hand from the fold of the strap (front) note Note exactly 1.0 cm. from the ends and not the entire length. I had it 44 cm from the ends (so that when you put the strap on the bag along the length, the mark reached the top bend). Build perpendicular to the cut of the strap and the shaded part of the cut.
Further, on the other half of the strap (on the reverse side) note 1.0 cm from the cut, also 44 cm from the ends.
Here is a picture taken as the basis of the application.
Pin a rectangle of red fabric to the front side of the pocket. Top center pin with a paper deer.
Fill in the sewing machine light thread. Set the stitch length 1 mm. And begin to sew right along the contours and lines of the drawing. On paper, through the lower layers tissue. It's okay if you walk through some areas twice. I did it deliberately to strengthen the contours and the way I wanted. When the whole drawing is stitched, remove the pieces of paper – convenient to clean ear with a big needle.
Cut the excess fabric along the contour of the figure, at a distance of 1.0-2.0 mm.
More carefully, with small scissors, make holes in the upper fabric in the figure – where you want. These are large areas where the pattern is too dense. In General, add air and openwork. Your application is ready!
Sew a pocket is a future seam with a closed cut.
Pin the pocket with the lower cut, the wrong side up to the previously marked horizontal line of the pocket position, placing between the same marked lines Sew, iron the pocket up.
The widest stitch, without tack, sew a pocket on the sides. This is a temporary line, when the bag is ready, remove the line. All right, pocket's in place.
Straps.
Fold the strap with the front sides inside. On the Central, not cut parts combine sections, fasten needles. Lay the seam at a distance of 1 cm from the cut. Hand just made seam smooth. Turn the straps. Bend the seam and ironed so that the seam was on the edge of the webbing without bias.
Take one strap. The side where we have marked 1.0 cm from the cut, apply to the previously planned line of the location of the strap on the bag. One end of the strap – on one side of the part, the other end – on the opposite side. Pin to the whole part of the strap. On the marked line and 1.0 cm from the cut – set lines. We do the same with the second part of the bag.
We iron the straps to the center. We fix the direction of the pins straps at the top of the bag, in the area of bending. Sew the strap at a distance of 2.0 mm from the edge along the entire length, without interrupting the line – through the free part of the strap going to the opposite side.
Fasten with pins the loose fit of the strap of the bag. And just one line at a distance of 2.0 mm sew the entire strap. Repeat this with the second half of the bag. We remove the temporary lines of the pocket on the reverse side.
Back to the top of the bag. Sew in the form of geometric "8": so that the fastening took place in 2.0 mm from the upper edge of the bag and 2.0 mm from the edge of the bend. Straps are ready.
Change the thread to light.
Fold the halves of the bags underside to each other. Cleave the needles on the sides. Build the seams on the width of the presser foot of the sewing machine (mine is 7mm) on both sides of the bag.
Iron the seams.
Turn the bag. Similarly, as did the straps, iron the side seams. Cleave the needles and lay the lines at a distance of 1.0 cm.
We iron ready seams towards the back of the bag (they should be ironed towards each other. Again, turn the bag on the front side. Iron the bag, bending at the side seams.
The top of the bag. Fasten with pins the hem of the bag. At a distance of 1.0 mm from the edge of the bend on the reverse side, we lay the lines, interrupting on the straps.
Bottom of bag. Combine the bottom of the bag, fasten the pins on the front side and lay the line on the width of the foot from the edge of the cut. In General, the bottom is treated in the same way as the side seams were treated.
The bottom of the bag. Combine the side seam of the bag with the seam of the bottom of the bag, as shown in the photo. Note the lateral seams of the resulting angle of 3.0 cm from the top, connect the points with a line. Lay on her line. Similarly, perform the second corner of the bag. To see that all of our seams looked in the right direction, not to twist (the seam of the bottom of the bag looks in the opposite direction from the side seams to avoid unnecessary thickness)
Small bag perform exactly the same as the bag itself, but without straps. A distinctive feature – bending 1.0+2.0 cm (on the bag was 1.0+2.5). And for corners enough to retreat from the top of 2.0 cm.
When bending the top will be ironed on one side of the bag on the front side, the center mark the position of the loops. The distance between the loops – 2 cm.
A small bag should not be located in the center of the bag! Lay a line between the marks made earlier. Ie bag should be sewn to the bag is not all bottom! And turn the face inside.
Your deer bag is ready! Below I have attached a photo-the instructions for its folding.
source: www.livemaster.ru
0 comments:
Post a Comment